Trusted since 2001 · Same-day response for emergencies · Call 951-458-6466
In Business
Rated
Contractors
Liability Coverage
Satisfaction Guaranteed
Who They're For and What They Solve
Garage door spring replacement is the removal of worn or broken counterbalance springs and installation of new, correctly rated ones. Springs carry nearly the entire weight of the door so the opener and your arms barely lift anything. When a spring snaps, that stored force disappears and the door becomes dead weight.
Anyone with a sectional garage door will need this eventually. Springs are rated in cycles, not years, so a door opened six times daily wears out far sooner than one opened twice. Homeowners, landlords, and property managers all call once the door stalls partway, hangs crooked, or refuses to move at all.
Replacement restores balance, protects the opener motor from burning out, and removes a real drop hazard. Springs hold enormous tension. Leaving a broken one in place risks a heavy door falling, a snapped cable whipping loose, or an opener destroying itself pulling weight it was never designed to carry.
Is It Time?
Most people notice one of these before the door quits entirely.
Our Services
Our garage door spring replacement covers every common spring configuration on residential and light commercial sectional doors.
Torsion springs mount on a steel shaft above the door opening and twist to store tension. This is the most common setup on modern doors. We wind new springs to the manufacturer's turn count, giving you a door that lifts evenly and holds position at any height.
Extension springs run alongside the horizontal tracks and stretch as the door lowers. Older and lighter doors typically use them. We install new springs with proper safety containment cables so a future break stays contained instead of sending metal across the garage.
Two springs share the load and fatigue at the same rate, so replacing only the broken one leaves an uneven pull. We install matched pairs, then calibrate tension and run a manual lift test to confirm the door stays put at waist height.
Standard springs are rated around 10,000 cycles. For doors used as a main entrance, we install heavier-gauge high-cycle springs rated to 20,000 or more. The upfront cost is modestly higher and the replacement interval roughly doubles.
Not sure which approach your situation needs? We assess first and recommend only what’s necessary, no upsells.
Why Homeowners Choose Mr. Local Services
Every truck carries a full range of torsion and extension springs. That inventory is why most spring replacements finish in a single visit rather than a return trip.
We inspect, then quote a written flat rate covering parts and labor. Nothing changes after that number is agreed to, even when a job runs long.
Both the spring and our installation are covered for five years in writing. A spring that fails inside that window gets replaced at no charge.
Before we pack up, we release the opener, lift the door by hand, and confirm it holds at mid-height. That test result goes on your invoice.
How It Works
Call 951-458-6466 and tell us what the door is doing. We identify the likely spring type and give you an arrival window on that call.
Our technician measures spring wire size, length, and inside diameter, checks cables and rollers, then hands you a written flat-rate price before touching anything.
We unload remaining tension with winding bars, remove the old springs, and install correctly rated replacements. Most spring replacements take 60 to 90 minutes.
We set final tension, cycle the door several times, run the manual balance test, lubricate moving parts, and haul away the old springs.
Pricing
We publish real numbers because guessing helps nobody.
Most single-door spring replacements run $180 to $360 for a matched pair, parts and labor included. Larger or heavier doors, high-cycle upgrades, and double-spring commercial setups typically land between $320 and $550.
Four factors move the price: spring type (torsion or extension), wire gauge and length, whether one or two springs are being installed, and cycle rating. Cables, bearings, or rollers replaced at the same time are quoted as separate line items you approve first.
Every quote is flat-rate and confirmed before work begins. There is no diagnostic fee when we complete the repair.
Yes, on two-spring doors. Both springs have absorbed the same number of cycles, so the surviving one is close behind and an uneven pull twists the door.
Most jobs take 60 to 90 minutes on site. Doors needing cable or bearing work alongside the springs may run closer to two hours.
We strongly advise against it. Springs hold hundreds of pounds of tension, and releasing that force without winding bars and training causes serious injuries every year.
Standard springs are rated near 10,000 cycles, roughly seven to ten years of average use. High-cycle springs are rated to 20,000 or more.
Sometimes. A snapped spring sometimes comes with worn cables or rollers, and our garage door repair service every hardware issue we correct so you know what a full inspection covers.
Yes. We are state-licensed, carry $2M general liability plus workers' compensation, and every technician is background checked.
Call 951-458-6466 before 4:00 PM and we schedule you that day. You get an arrival window on the call, not a vague all-day promise.
A broken spring will not improve on its own, and every attempt to force the door open costs you more in hardware. Call now for a flat-rate quote and same-day replacement backed by our 5-year warranty.
